Welcome to the Products Page
Color Changing Flipper Button Kits For Williams/Bally And STERN Pinball’s
These Come In Two Types: FAST Color Changing LED’s and SLOW Color Changing LED’s
The Williams/Bally CCFB Kit fits all WPC Types With A Coin Door Interface Board And Fits Pins With The Optical Flipper Buttons.
The STERN CCFB Kit Fits All Newer STERN, 1999 – Forward And Most SEGA Pinball’s (Please Check With Me On The SEGA). Almost No Light Bleed Under The Apron Or From The Shooter Lane Like Some Others Currently On the Market. I Will Also Build Them In Any Single Color Led That You Want 45.00 US Each Set + Actual Shipping
Fast Color Changing Flipper Buttons: Link
Slow CCFB’s: Link
Close-Up of Slow CCFB’s: Link
TRON Legacy Recognizer MOD
Fits Both TRON-LE &TRON-Pro Pinball Games, These are $42.00 each + Actual Shipping Costs, They Can Be Ordered With Two Different Wiring Harnesses & Two Different Color Down Lights (All Come With Orange/Amber Up-Lights To Emphasize The Cabin Plastics).
LED Down-Light Color Choices:
-Bright Deep Blue LED’s
-Bright Cool White LED’s (Kind Of A Brilliant Bluish-White Light)
Two Wiring Harness Types Are Available –
12V OR 24V Wiring Harnesses Both Wiring Harnesses Fit TRON-PRO & TRON-LE.
The 12V Wiring Harness – Ties Into The 12V Source Near The Coin Door And The Recognizers LED’s Are On All The Time.
The 24V Wiring Harness – Ties Into The Spinning Disk Motor Wiring Harness & The Recognizers LED’s Are On ONLY When The Recognizer Is Actually Moving – LED’s Are Off When Recognizer Is Stationary (Middle Position & Stopped) & Off Very Briefly At Far Left & far Right (When The Recognizer Changes Direction).
If You Can’t Make Up Your Mind, Order Both Wiring Harnesses For An Additional $8.00 ;-})
I Can Add As Many 12V/5V Splitters To Your Wiring Harness Depending ON How Many Other MOD's You Have In Your Game @ $8.00 Each
LED’s (Blue) On All The Time: Link
LED’s (Blue) Only On When Recognizer Is Moving: Link
TRON-LE Recognizer with Cool White Down-LED’s: Link
TRON-LE Recognizer with Blue Down-LED’s: Link
Iron Man MODS:
Whip Lash MOD $150.00 Comes With New WL Figure, On New Lower Mounting Laser-Cut PETG Plastic, Chest LED Ties Into GI,
The WL EL Wire/Strobe Driver Is Powered By 2 AA Batteries (So Far It Has Already Lasted Well Over 2 Months In home use).
Iron Monger MOD $75 + I Need Your IM Figure To Install Into As They Are NLA From STERN.
War Machine MOD $60 + I Need Your WM Figure w/Cannon As They Are NLA From STERN, Chest LED Ties Into GI,
+ $15 If You Want An LED In The Cannon Which Ties Into The Blue WM Flasher
Drone MOD $85 Comes With Figure, On New Lower Mounting PETG Plastic, Chest LED Ties Into GI.
If You Don’t Like To Solder I Can Add Alligator Clips To Any Of Them For $5.00 Per Pair Of A-Clips.
Iron Man-Link
Twilight Zone Clock Upgrade to COLOR CHANGING 5mm LED's $80.00
NOTE / Caveat; - Your Clock Must Be Working 100%, While I Can Repair The Cause Of Your "Clock Error" Issue It Will Be At My Regular Repair Rate + The Parts Required
This Upgrade Will Typically [but not always] Cure The "Clock Error" Message As I Will Re-Flow EVERY Solder Joint For Each Component On Both Boards I Will Also Check The Alignment & Operation Of The Minute Hand [A Common Cause Of The Clock Error Message] As A Part Of My Quality Check-Out For The LED’s Installation & Burn-In And An Operational Verification & Final Check-Out In My TZ Game
Twilight Zone Clock Upgrade: Link
Twilight Zone Clock Upgrade to SuperBright White 5mm LED's $50.00
NOTE / Caveat; - Your Clock Must Be Working 100%, While I Can Repair The Cause Of Your "Clock Error" Issue It Will Be At My Regular Repair Rate + The Parts Required
This Upgrade Will Typically [but not always] Cure The "Clock Error" Message As I Will Re-Flow EVERY Solder Joint For Each Component On Both Boards - I Will Also Check The Alignment & Operation Of The Minute Hand [A Common Cause Of The Clock Error Message]
I Can Also Upgrade Your TZ Clock To 10mm Superbright White LED's For An Additional Charge Of $15.00 To Cover Their Higher Cost And Additional Shipping While I Don't Typically Reccommend The 10mm LED's Due To Their Almost Overwhelming Brightness In The Clear Clock Housings, However They Look Awesome In The Colored Clock Housings That Were Recently Reproduced And Are Still Available From Mantis Amusements Link
SOON TO BE AVAILABLE - Robbie The Robot Upgrade For Your Twilight Zone Pinball !!
All Shipping Charges Are The Responsibility Of The Buyer - For Parts Ordered & The Return Shipping Of Your Parts/Items